Bullet resistant acrylic

Bullet Resistant Acylic

Plastiglas de Mexico is proud to introduce their UL approved Bullet Resistant acrylic sheet for use in banks and other security areas. Chemcast BR is available in 1 1/4" thickness in 48"x96" and 60"x96"sheet sizes.

For more information, call your local Chemcast distributor or email PlasticsOnLine.

Click Here for UL Report

Sensacril - FP

Sensacryl FB is a specially formulated cross-linked cast acrylic sheet designed for the sanitary ware market. It is available in virtually all the industry colors, whites, pastels and marbles with color matching readily available. Sensacryl is available in cut-to-size for specific requirements subject to quotation.

Sensacril FB has excellent chemical resistant properties enabling it to be in contact with commonly used household cleaning agents. Also, the cross-linking allows Sensacryl to be thermoformed in deep draws with excellent uniformity particularly at sharp corners.

PRODUCT INFORMATION

SANITARY WARE TESTS

Sensacril FP has been tested by an industry approved independent laboratory for compliance to the ANSI Z 124.1, UL 746C and UL 94HB standards for plastic materials used in hot tubs and associated equipment. The test results complied exhibiting excellent chemical and stain resistance, accelerated aging resistance, cigarette burn resistance and low water absorption.

THERMOFORMING PROPERTIES. Sensacryl FB shows better thermoforming properties than general purpose cell cast acrylic sheet. It's advantages:

	Sensacril FP can be thermoformed much more easily because it takes less force to thermoform parts.
	Sensacril FP will stretch considerably further without rupturing.
	Sensacril FP has improved thermal stability allowing a more flexible thermoforming process for complex parts.

FORMING CONDITIONS

	Sensacril FP is ideally thermoformed in a temperature range of 335-390 F (180-220C) with a cycle of 10-14 minutes in a hot air circulating oven.
	The actual cycle temperature settings and techniques most suitable for a particular job are best determined in the customer's own equipment. The following charts give a general guideline about heating times as a function of the sheet thickness for air circulation ovens and infrared heating.

TABLE 1.

SENSACRIL FP CAST ACRYLIC - SANITARY GRADE PHYSICAL PROPERTIES

PROPERTY	TYPICAL VALUE	UNITS	TEST METHOD
MECHANICAL	.	.	.
Tensile strength (min)	60	Mpa	ASTM 638
Elongation (min)	4	%	ASTM 638
Izod impact strength (notched)	0.924	kj/m2	ASTM 2583
Barcol Hardness	48	.	.
.	.	.	.
THERMAL	.	.	.
Hot forming temperature	180-220	°C	.
Heat distortion Temp (182mpa)	90	°C	ASTM 648
Thermal Stability (30 minutes at 180° C	No evidence of degradation	.	.
.	.	.	.
MISCELLANEOUS	.	.	.
Flammability rate	15	mm/min	ASTM D635
Flammability grade	94 HB	.	UL 94
Chemical Resistance	O.K.	.	ANSI Z 124.1
Cigarette Resistance	O.K.	.	ANSI Z 124.1
Stain Resistance	no evidence of degradation	.	ANSI Z 124.1
Water Absorption	35	mg	ANSI D-570

(1) All values referred to 3.0mm (.188") acrylic sheet. These values are typical and should not be taken as a specification.

TABLE II

sizes (mm)

2440x1830

2440x1220

1830x1830

1830x1220

2540x1300

Thickness

Colors

Whites

Bolds

Pastels

THICKNESS TOLERANCE
+/- 10%	.	+/- 20%
1830x1220	.	1830x1830
2440x1220	.	2440x1830
2540x1300	.	.